Chosen Solution why is my front end shake and vibrate? swamprate750, there are many reasons why this could be. Check your tires, your brakes, your wheel bearings, your tie rod ends, your ball joints, check your alignment and plenty more. This is something your have to be systematic about the trouble shooting and do one thing at a time. My first approach would be the tires and front suspension parts....
Chosen Solution HI I have a iphone 5 and the glass of my screen was cracked. I bought a new lcd with digitizer from ebay and replaced that with an old cracked one. It works fine but the even though i changed setting to full brightness, it’s not bright enough compare to my friend’s iphone 5. Auto-brightness is turned off So I replaced it with my old one but still darker than others....
Chosen Solution Where is the correct fuse for cigar and middle console power outlet Hi, I don’t know your vehicle but according to the owner manual for a 2000 Ford Mustang (you don’t state the year model) the fuse for the cigar is fuse #1 in the passenger compartment fuse panel. The fuse panel is located below and to the left of the steering wheel by the brake pedal. The manual also shows that fuse #9 in the engine bay power distribution box is labelled as Auxiliary Power Point which may be worth checking out to see if this is the one for the console power outlet....
Chosen Solution Hi all I have a problem and was wondering if anyone else had this. Was repairing a 4s today and the screw on the battery connector was completely striped and I was at it for a hour with no joy. I’ve heard of people using a little bit of glue but I don’t think it’s possible as the screw seems to tight. Was wondering if I let the battery die could I take out the motherboard and battery and the speaker in one peice as the reception wire is attached to the motherboard aswel....
Chosen Solution Recently replaced battery in 3GS. Everything worked fine for a few days. Now when I press the Home Button nothing happens. If I press the On/Off button I get the home screen. If I plug in the charger I get the home screen. But nothing happens when home button is pressed. Thanks for your guidance. Millsp2000, It seems your home button is unresponsive, that may be due to when you replaced the battery you touched the two pins of the home button,which might of short circuited it....
Chosen Solution How can I change the speaker and from where I can buy it ? Ifixit has a service manual that gives instructions on how to remove speakers from your XPS 15z at the link below. The speaker removal starts at page 44. xps-15z_service-manual_en-us.pdf As for where to find parts, I would suggest you remove your speakers to verify the part number, and then just do a search in your browser for your part number....
Chosen Solution Is there an easy way to remove a virus from my computer without removing and replacing the harddrive Here is a link to a free Microsoft program for removing a virus with instructions on how to proceed. Good luck. http://windows.microsoft.com/en-US/windo… the best its download a malwarebytes in a dvd or usb flash drive from another pc who doesnt have virus and then enter in safe mode in your pc and run it...
Chosen Solution This piece got damaged in my car. Hi @alberte27 , Not sure what you mean by “centre control cover” but if you mean the service cover, here’s a link to the service manual for your laptop, taken from this webpage Scroll to p.40 to view the necessary pre-requisite steps and then the procedure to remove the service cover. Also on p.40 are the part numbers for the various covers available....
Chosen Solution please help me to find the exact location where i can find the model of my laptop. my laptop is 2008 vista hp pavilion notebook entertainment. Hi Follow the instructions listed here - https://support.hp.com/ca-en/document/c0… - there’s usually a tag on the back/bottom of notebooks that list the model #, but if you can’t find it, the instructions above will have that info for you.
Chosen Solution Mod #FGID2466QF2A it was mark pf on the touch pad not light came on the touch pad. i change the control baord and it did not make no difference. Cause 1 Thermal Fuse The thermal fuse shuts off power to the dishwasher if it overheats. If the thermal fuse blows, it will prevent the dishwasher from starting. To determine if the thermal fuse is defective, use a multimeter to test the fuse for continuity....
Chosen Solution Hi, does anyone know if you can use an earlier display assembly on this model. Can’t find a 2015 display assembly listed anywhere. Thanks The backlight Pin out is different on 2014 and 2015. They look the same and fit perfectly but the backlight boost circuit is different and pins are in different position than 2014 models. So, if you know how to redo the traces and manually jump the rails that will work....
Chosen Solution If I purchase 3rd party RAM upgrade for this Late 2018 MacMini, and install it myself, will that run afoul of the T2 chip? I usually upgrade via OWC for myself and my clients. I am trying to clear the air for the 480 readers of my daily newsletter. You should be OK doing so. I believe the T2 chip only time bombs major stuff like the logic board....
Chosen Solution Hi, really quick question that I can’t seem to find the answer to: Do I need a new logic board to install a new heat sink? My Macbook (late 2008) has a partially blackened heat sink, and the guy in the Apple store said I need a new one AND a new logic board to go with it. I’m not adverse to a bit of DIY - is it possible to just buy a new heat sink and (using your guide) stick it in myself… rather than shell out for a whole new logic board?...
Chosen Solution I have a Kenmore 700 series and it shows f-5 code. I believe it keans the water temperature sensor. Every time we would want to wash inly hot water would come out. My question is : What is the cause How do i fix it Where are the parts located at Thank you . Hi, What is the full model number of the washer? What happens when you select cold water only?...
Chosen Solution Face ID works perfectly in dark and dim lightning. In the sun it fails 90% of the time. What do you think causes this? Probably a faulty screen or you mis-aligned the earpiece causing this issue.
Chosen Solution I am having issues locating firmware for the galaxy note edge, this model number in particular; SM-N915A. Sammobile does not have it listed, and I have not been able to find it anywhere else. Has anyone found this or had this problem before? A link to a site that has it would be amazing. I have seven now that need it that! Thank you! Found some here: http://androidromupdate.com/att-galaxy-n… More here: https://www....
Chosen Solution My 13 inch MBP does not boot with the recovery partition missing or startup disk missing. Tried to boot it with “Option + R” combination but it did not work. It took me to the internet recovery mode through wi-fi. I followed the link http://www.macworld.co.uk/how-to/mac/res… I opted for preparing a bootable installer on flash drive. Using another mac succeeded in making a flash drive with “Install OsX El capitan app” and followed the instructions exactly as given in the link....
Chosen Solution Hi all, we’ve got a much loved “R4” card which contains 70 games ?on what looks like a smaller ?SD card.It no longer loads on the games console…just shows " loading". Considering the ages of the people owning the nintendos and the number of times I have replaced the hinges/screen I would guess that it has suffered a “life threatening injury” of some sort by one or more of the owners!...
Chosen Solution Hello! i have an Apple iMac “Core 2 Duo” 2.66 24-Inch (Early 2009) and im wondering if i can upgrade the graphics. i got as far as removing the screen and then i figured out i need a screw driver… before i do anything else i want to know if its even possible. im thinking at least 1GB of vram if its possible i would love to hear if it is....
Chosen Solution Hello, have the Poulan Pro PP6000H hedge trimmer attachment for some time. Lately I noticed it is not cutting as it used to cut. checking it I found that the blades are not timed and so from time to time almost move together instead of opposite directions. I opened the unit and found out that the lower blade is getting off the eccentric block. I tried several times to put it back, assembled it but still after running for a minute or two correctly, it happened again....
