Chosen Solution I have put the hot air station to 450 degrees and the module will not even budge any idea please i also tryed on the nor but same. The Ps4 was in storage for some time does this effect the solder. there is no way to put quick melt solder on pins as they are under.Any help please Unless you have the board sitting on a pre-heater 450 degrees would not produce enough heat due to the large ground plain on the PS4....
Chosen Solution Title sums up a good TL:DR of my issue; but to elaborate, I have managed to clock the frequency of this forced restart (more like a constant crashing, like a system-wide memory leak or critical process failing) at ten minutes with little to no deviation based on my PC’s time. It’ll keep doing this for a few hours, the duration of the issue does vary. As I’m typing this, it finally stopped doing it about twenty minutes ago, and started two and a half hours ago....
Chosen Solution Wifi antenna are at the base of the unit. If sitting on its side or upside down the device’s wifi RSSI, Quality and TX Rate improve significantly. Noting the ventilation design, can the device be used in alternate orientations? First: are you having a problem with WiFi signal? I would start with your router rather than the Studio. After reading your post I moved my Studio to a spot in the house that gets the worst signal (in a nook in the kitchen behind a concrette wall & the refrigerator) and was still able to get almost full-speed (Gigabit) downloads and uploads....
Chosen Solution I cracked the screen on my iPhone 8 so ordered a replacement off eBay. It’s not a genuine apple. I switched the home button over, installed the screen, turned the phone on and the phone was acting really weird. It was really slow to boot, did not find mobile network signal it just displayed ‘Searching’ and then the screen just went black - the screen was actually quite responsive before this point though....
Chosen Solution My camera keeps displaying a message that says ‘change the batteries’. Why is this? @tyiilliamani, Kenzo , Ensure that the battery contacts are clean and install a new quality set of fully charged batteries and if using rechargeable’s have charger tested or try another known good working compatible charger to rule it out as an issue. Possible internal clock battery may be faulty (change internal CR1220 battery) or issue with bad components in camera....
Chosen Solution I recently obtained a winch for my ATV. I mounted it with the cable winding and unwinding from the top of the spool, not the bottom. After mounting it, I found that the cable is supposed to wind and unwind from the bottom of the spool, not the top of the spool. Does it matter which way it is mounted? https://www.harborfreight.com/2500-lb-at… Your controls will be reversed. Instead of winding up it will be unwinding....
Chosen Solution Can I use A Hitachi Travelstar 2.5" Internal Hard Drive. It is 500 GB and 7200 rpm.My son and I put one in and I havn’t been able to get it to load the install program. Your installation instructions wher great. Thanks Greg Haines Has the drive ever been formated MS-DOS? If so you may never be able to use it in a Mac. If it is a new drive, it should work fine....
Chosen Solution washer shakes and makes loud noise and moves drum seems to be llose any way to tghten drum so it doesnt move around so much Tub Bearing If the washer is making a loud noise the tub bearing might be worn out, this is a common problem. The bearing can be replaced. On some models the bearing is part of the outer tub and the outer tub will need to be replaced....
Chosen Solution My ipod fell in sink and it turns on but it turns back off! Any help Andy Lamb, you need to treat it for the water damage. Disassemble your iPod by using these guides. Then clean it using isopropyl alcohol and a soft brush, just like it is shown here. That guide was written for a iPhone, but all the steps still apply to your iPod. After that replace the battery, reassemble your iPod and re-evaluate for further, if any, damage....
Chosen Solution Hi all! After my recent mishaps with a MacBook Pro I’ve decided to try and fix another thing, my SE. I got the phone around half a year ago with a broken screen, faulty flash and mute switch. I then went about replacing the whole housing and sceeen with an iCloud locked phone and all was well until around 2 months ago. Every few days, if the phone is vigorously placed on a desk or handled too hard, either the flash, mute switch, or volume buttons or even the vibrate motor will totally stop working....
Chosen Solution My Fridgidaire PHSC39EJSS0 freezer is not going below 32 degrees. Both the condenser fan and the evaporator fan struggle to run as soon as the temp reads 32. The fans run for about 3 seconds before cutting off. However, if I leave the door open so that the temp gets to 40 or 50 degrees, both fans run fine until the freezer gets to 32. The evaporator coils were slightly covered with frost and I allowed it to melt- it didn’t help....
Chosen Solution Full charged iPhone 4 battery is not working after 60% battery remaining,why ? Sounds like the battery is at fault. I suggest replacing it with a quality replacement battery from iFixit. You can get a replacement battery from here: iPhone 4 Battery Guide to replace the battery: iPhone 4 Battery Replacement
Chosen Solution Hello What function do the red circled copper pins do have, which are “all over” the logic board of e.g. my MBP A1286 or A1297? One of them has been broken and it seems as there is a copper line below it on or within the PCB. Picture has been attached. Regards, Stone Update (08/23/2013) And the location of the sound chip itself, labeled with u6200 … http://root.dietmarstein.com/tmp/a1297/p… http://root....
Chosen Solution Hey, I recently performed a screen replacement on an iPad 2 and everything looked good, but after I entered the pin for the first time, the device immediately went into the calendar. Reading various tips on this site, I found that the “ghost touches” were often a result of contacts being triggered and that taping the connections on the underside of the screen would solve that issue. To test that this was the issue, I booted the device and entered the PIN while the screen was off (so that nothing could possibly be touching the contacts inside) to test that this was indeed the issue....
Chosen Solution Can I upgrade my hard disk raplacing it whit an SSD only following the replace hard drive’s guide on ifixit? Sure, just make sure to use the jumper pins to take it down to 1.5 GHz if disk utilities won’t see it. I’ve done this with an ocz agility 3, works fine at SATA III (6Gbs). i have ssd samsung SM841n function perfect
Chosen Solution Hey in 16 and I’m fixing this dudes iPhone 6 plus screen and we have ran into a problem. Our problem The problem is we have tried two different screens on the dudes iPhone and they both work at first but then become unresponsive. Ok so in thinking maybe some connections are not tight enough. You know the right part of the phone where the cam and sensors and screen connections are?...
Chosen Solution Hi! Been a while since I’ve been on Ifixit. I need help with installing Niresh 10.7. When I boot it up, it says a bunch of stuff, then it ends with cdboot: error. How do I fix this? Help will be much appreciated Don’t use niresh, it’s horrible. Just use UniBeast and make a USB. Here’s how: http://tonymacx86.blogspot.com/2011/10/u…
Chosen Solution Hello everyone I’ve got quite a story for you. I bought these two iphones (iphone 5s and iphone 5) from someone on Craigslist list for $50 in the description it said they don’t turn on so I thought it was an easy fix, I’m thinking it could be stuck in DFU Mode or even simply get a new battery for both. Well I got the iphone 5s out of DFU but the speaker wasn’t work and the home button wasn’t either....
Chosen Solution It has a battery problem and it won’t turn on, the problem is that I don’t really have experience with fixing things. Should I get a new battery for it or what? Or should I get it taken in somewhere local and professional? Hi! Replacing the battery on the Nintendo DS Lite is extremely easy: all you have to do is unscrewing that small philipshead on the bottom of the unit, to the right of the SLOT-2....
Chosen Solution does not start. what to check to see why David, More info would help to point you in the right direction. Basically you need Ignition, Compression and Fuel Compression- Is engine turning over or cranking (battery, connections, starter, relay) Fuel- Are you getting gas to cylinders (fuel, fuel pump,injectors and sensors) Ignition- Spark to to cylinders (spark plugs, ignition coil, plug wires and sensors) Hope this gives you a direction, Glenn Update David, Check this out https://wiki....
