Posts

Chosen Solution Fan comes on, but no heat comes into cabin. Troubleshooting ideas? John Blaine, check for a few more things like : Make sure the blower works all the time, Check to make sure that the cooling system is full, Check to make sure the engine heats up to operating temperature, and make sure that all the modes on your heater operate. If all those are satisfactory, it is posible that you have a blend door actuator problem....

Chosen Solution I have a kenmore washer model 110.44722401. A lot say it is the lid switch but it is clicking, and why would it fill and agitate if it was lid switch TEST IT. Lid Switch Assembly If the washer won’t spin the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity....

Chosen Solution I changed the screen to my A1554 Apple Watch. When taking the shattered screen off, I didn’t realize there was some kind of a sensor so I tore it off. I replaced the screen with a new one and assembled the watch since I didn’t have the a new sensor. Now, however, force touch is still working just fine. What’s the purpose of that adhesive ring? Do I need to get one?...

Chosen Solution Hello I have an iPhone 5 that works good only when it is hand-held. When the phone is on the table(and the case has no contact with the skin or any GND), the touch does not work at all. Thanks Probably a fault caused by a replacement screen. Aftermarket one most likely.

Chosen Solution Just bought the used S7 on ebay and immediately noticed how bad the camera is on this. Seems like I’m always out of focus/softened/blurred whether in the camera app or snapchat. (All beauty settings are down to 0). Is something broken or what? Is the camera focusing at all? If not, the rear camera needs to be replaced. Here is a guide in case you decide to replace the rear camera: Samsung Galaxy S7 Rear Camera Replacement

Chosen Solution Hello everyone My iMac has stopped working and I need to replace my Graphic Card, do you know what is a good choice for one compatible with my system? Your system came with a ATI Radeon HD 2600 Pro with 256 MB VRAM - Apple P/N 661-4426 Sadly you really can’t use anything else as the version of MXM interface your system has won’t support any of the newer boards....

Chosen Solution Hi, i am interested to purchase this hard disk to my unibody a1278 http://www.amazon.com/gp/product/B0034ZD… Let me know if it will be 100% compatible or wich its the biggest i can install on it. I got also confuse because in iFixit store and also Apple Store page the maxium hard drive avaible for purchase for this mac, its 750GB ¿why not 1TB avaible? Does its overlock the mac? Best regards....

Chosen Solution Hi, I have Macbook pro 1,1 A1150.. 2GHZ [Up to Dated SMC and firmware] The system fans never kicks in, It seems that they stay at 999 rpm even with high CPU usage and it is burning hot.. I ran Apple Hardware Test and all test are passed…. When I ran the temperature software it shows the temperature of CPU idle 50+C and the Fan is 999 RPM.. I even installed iCyclone to control the temperature it does a good job but only if you are inside OS....

Chosen Solution Playstaion 3 80gb Red Light 3 beeps, pls help can i fix my ps3 with tha YLOD kit fix? While there is no direct guide to do this, this generic guide should answer your questions: Technique: Applying Thermal Paste. As to what you’ll need: Arctic Silver ArctiCleanArctic Silver Thermal Paste

Chosen Solution Hi all, I replaced the home button on an iPhone 6 Plus I purchased. I know I lose touch ID when I replace, however, this button won’t even function as a home button. I’m on the setup screen and it says press the home button to open and when I press it nothing happens. Is there something I’m missing here? Does Apple entirely disable replacement home buttons? I’ve had this issue once before with a 6S but the user didn’t mind so I left it like that....

Chosen Solution hey there, i repaired a iphone 6s screen and after it was done the home button wont work, it clicks perfect but wont do annything + touch id wont work to. but it was a screen with the home button cable already attached , can it be the new screen? or the installed lcd shield? thanks for reading this. greetz It could be the screen, since now the home button wiring goes through the 3D touch sensors....

Chosen Solution I want to adapt my Marantz turntable in a USB turntable. How can I modifie The OUT cable with 2 old connectors in a USB or fire wire cable. If I can do this I think I’ll be able to connect it to my Mac Book Pro with LogicPro X software or proTools. Is it possible. I know that USB turntables exist. But I already have an excellent turntable....

Chosen Solution I want to use again my an iPhone 3g!! Is there anyway to get to run on it the latest version (or one where the latest apps run on) of iOS? If not all the apps will not work and the phone will be useful!!! Please help meee!!! Best Emanuele Unfortunately, the last version of iOS that the iPhone 3G will support is iOS 4.2.1. Obviously, many, if not most, new apps will not run on this version of iOS....

Chosen Solution How do I add storage memory and needed parts/memory. Also, how do I determine if I currently have the maximum allowed storage memory. Thank you, James To start with here’s a spec sheet on your system: HP EliteBook 8530p Notebook PC Here’s HP’s memory upgrade guide for your system: Memory Modules User Guide. You’ll need the following: DDR2 SDRAM, 800 MHz 1024/2048/4096 MB SODIMMs Total memory supported = 8GB...

Chosen Solution I am unsure what type of HDD my iMac has. I am 99% sure it is not a SSD, based on performance. I do I know if I can replace current HDD with a SSD? Your mac will 100% will be able to take a ssd. The prices on them have dropped a lot in the last year and i would stick to a well know brand ie( samsung, sandisk) while buying one....

Chosen Solution My phone is flashing the apple screen and when i hold the power button it will not turn off. I need to reset it. Please help? DFU Mode. Open iTunes on computer. Connect iPhone to computer with USB cable. Hold both Home and Power button, after exactly 10 seconds release the Power Button, keep holding the Home button until iTunes recognizes iPhone in Recovery Mode, usually about 20 seconds time....

Chosen Solution i have a iPhone 6 which was water damaged. Im hoping for data recovery, i took all emi shields and cleaned corrosion away. BY using schematic i found the speaker ic was causing problem and removed that, now i have a problem with capacitors around the baseband chip and also ‘c1417’ which i believe is to do with charging, if i was to remove this to try shorting would it affect the charger port so the phone wouldn’t turn on?...

Chosen Solution Basically my mother’s iPhone 5c was dropped in water and she put it in rice for 2 days. The phone can turn on but with very visible damage to the screen. The touch screen is broken and doesn’t work at all. This wouldn’t have been a problem if she didn’t have a 4 digit code for unlocking the phone because I can’t connect the phone to my pc since I need to trust the device on the phone before I can access the phone’s data (mainly photos)....

Chosen Solution I smashed my iPhone 6. I do minor repairs on iPhones. I replaced the screen on my iPhone. It worked good for a while than touchscreen would freeze. ( home , volume, lock button worked ). I had to do hard rest to make it work again. I assumed faulty screen, then I tried and 5 different screens, but the results were same. Two days later I was in face time, than phone heated up and died....

Chosen Solution I worked on a dead iPad today. The owner thought the battery was dead and so brought a replacement obtained from eBay (in fact, a complete rear shell with battery still glued in place). The original battery indeed read 0V - evidently it’d gone into protective hibernation, but the replacement read 2.5V - probably on the verge of going into hibernation. (Probably not a lot of life left in it, but that’s not my concern for the moment....