Chosen Solution My company was recently throwing away a Beats Pill+ that has been “flashed”. They told me I could have the speaker if I wanted because it was going in the trash anyway. The flashed Pill has been reprogrammed to only work with an aux cable and when it is plugged in. The Bluetooth and charging capabilities have been disabled. This was done in case someone stole it during our expo they wouldn’t be able to sell it....
Chosen Solution I let my son use my Imac G$ and he changed my passwords I need to restore my G4 since he brought it back to me but He forgot his password also. Start up from your original system installation DVD or retail 10.5 by inserting the disk and holding down the “C” key on start up. Go to the second page pull down menu to Utilities > Change password and change it....
Chosen Solution Hello, I have a Hotpoint fridge freezer FFP187MP which came in the flat I bought. Initially, this fridge was working well, however, when the door of the fridge was opened the lights would flicker 3-4 times with a clicking noise, before staying on. Recently I noticed the compressor comes on for a few seconds, then the same loud clicking noise happens and the compressor shuts down. After a few minutes, it happens again....
Chosen Solution My grandson dropped his switch from about three feet onto carpet now screen is fuzzy can’t see games so cannot play fortnite very upset grandkid kenweb10 since this happened after it got dropped my first suspect would be a bad LCD. Open up the Switch and look at the ribbon cable s make sure those are all still properly seated etc. If so, I’d replace the LCD next Nintendo Switch LCD Replacement
Chosen Solution troy bilt riding mower gas pedal goes all the way down but lawn mower will not move Likely the reason your tractor will not move with foot pedal depressed is that the drive belts are stretched and worn so the transaxle pulley is not grabbing and turning enough to engage transmission gears. One or both belts could contribute to this problem. So it is best to replace both upper and lower drive belts unless you have recently replaced one of them....
Chosen Solution My GE refrigerator works fine. The freezer does not. I have thick frost on the bottom and bottom left of the evaporator. What could cause this? How difficult is the fix? DIY? Thank you, Bryan This is a simple way to determine if the problem is an easy fix or not. Unplug the unit. Remove the back panel in freezer section. Be careful, edges and evaporator fins are sharp....
Chosen Solution Hi, I want to upgrade a 27” 5k 2019 iMac that has a fusion drive in it. With the Big Sur update, it became horribly slow. The fusion drive was probably a poor choice from the beginning. It’s my mom’s mac and she was scared she wouldn’t have enough storage with a 250GB SSD, even though I explained to her that internal SSD + external thunderbolt drives were the best choice....
Chosen Solution My son’s iPod Touch 6 Gen had an issue with the sound not coming out of one ear when he plugged in his headphones. I thought the easier solution would be to get him Bluetooth headphones, but the sound only comes out of one side of those as well. I used his BT headphones with my phone and they work fine. Has anyone seen this before? Any ideas?...
Chosen Solution So I have this issue her right now. A customer came in with broken screen, changed the screen and homebutton was working fine no damage to the homebutton or anything.. after three weeks he came back, I replaced the screen and homebutton was working again.. now he came back again and the home button is not working anymore with “assisive touch” on screen. Anyone know what the issue is?...
Chosen Solution The power button on my iPod Nano 6th Generation is stuck. As in, my iPod won’t turn on unless I plug it into the computer to make it light up. Please help! So, I actually got it fixed about three days after I posted this. Sorry for not telling everyone sooner! I had my warranty on it, so I took it to the store I bought it at and they replaced my iPod....
Chosen Solution The computer gets hot a few minutes after turning on and I think it might be overheating. It has shut down after extended use. Your airflow vents may be covered with dust or something else blocking the computer from cooling down properly. You can use compressed air to remove dust from vents and fans. The problem may also be stemming from where the computer is mainly used. Click this link for more help: HP EliteOne 800 Troubleshooting
Chosen Solution I’m really excited about getting an HTC Evo 4G when my current contract’s up in July, but company policy is no cameras at work, including on cell phones. Phones with disabled cameras, however, are permitted. Thanks to your teardown, I can see that the forward facing camera is pretty easy to remove, but it’s still hard to tell how difficult it would be to remove the main camera from the circuit board....
Chosen Solution I’ve tried to disassemble it but the cylinder thingy is frozen. It seems to be frozen in the locked position, even though I’ve used both the key and the thumb lock to try and unlock it. lauraevalentine , If this lock set is still installed on door, through the key slot, liberally squirt penetrating oil/ WD40 with a small injecting straw/nozzle and insert key in and out/wiggling and repeat several times till lock set works....
Chosen Solution Edited for cleanup purposes My LG G4 (H810) locked up, died when I pulled the battery and no longer turns on. At this point the phone is over 1 year old and is almost certainly out of warranty (or any “hidden” warranties). Neither AT&T or LG are probably going to help and I am likely limited to OOW repair. I have a 509K* phone, so mine is part of the bad range....
Chosen Solution No sound. Looks like one of three cylinders split and leak onto the board. Robodigger66 , this “three cylinders split and leak onto the board.” sounds like you are having some leaky caps. take a couple of images of the PCB and the “cylinders” so we can help you further.
Chosen Solution Hi, I have replaced a broken screen on my IPAD AIR 2. I purchased an OEM digitsier and LCD full assembly. After fitting the screen and turning on the digitiser will not respond, however the LCD works fine. I have not yet transferred the home button as I am awaiting a replacement so this screen is currently without a home button. My question is: Should the digitiser still respond without the home button?...
Chosen Solution Whirlpool wdf320padb3 dishwasher will not run a complete cycle. It will start, fill up with water and seem to get hot, but stalls from there. It will drain completely if select the button. I’ve checked the drain lines, cleaned out filter, but no luck. Any idea what might be wrong? Hi, Have you checked the water temp in the dishwasher hot water supply line? The temp of the hot water supply should be 120 F If the inlet supply temp is OK there may be a problem with hi limit thermostat....
Chosen Solution Sir my laptop is on but display is not comming… Sir please tell me technical and internal circuit problem and please send me to varmarajnikant7051varma@gmail.com .. please .. please .. please Sir i also check display cable , RAM change , laptop on off and battery change but cant it Hi, Connect an external monitor to the laptop and check if its’ display is OK. If there is no display showing on it either, then you either have a GPU problem or a motherboard problem....
Chosen Solution drivers side door seems to be jammed shut Try this https://m.youtube.com/watch?v=sHMe-5VpxM… Is this just the outside door handle that won’t open the door ? You have tried the inside release handle….does it work normally ? These issues are usually the result of the failure of the crummy plastic linkage clips that automakers use on modern autos. Requires getting door open usually you can get that done by removing the inside trim panel to get at the lock linkage directly....
Chosen Solution So I recently replaced my battery and home button and everything was perfect, but today I dropped my phone and it fell flat on its back (in case) and now the touch screen isn’t working properly, though sometimes works for a few seconds or minutes when I open it and goes back to being crazy suddenly, and the lcd has white lines through it (they appear after a few seconds when I open it)....
