Posts

Chosen Solution I’ve just finished replacing the screen assembly on my wife’s iPhone 6s and now neither force touch nor the home button / Touch ID work. The screen works fine however. I notice ice that this screen seems thicker than the previous one, I’m comparing it to my 6s which is about 1mm+ thinner now. Perhaps I have the screen improperly seated? thanks, robert Aftermarket screens tend to be a little bit thicker than OEM screens....

Chosen Solution My 2011 G29 48V Yamaha golf cart wont go into reverse or drive. No beeper sound when in reverse either. Battery levels are full, and lights are on, charger shows a full charge. Dave Dreer could be an issue with the controller as well as a fuse and many things in between. I suggest you start checking the wiring and see where you have power and at what point you do not....

Chosen Solution Battery back up not working @nytryder26 first replace the backup battery. Check the battery connector for corrosion and continuity. Trace the wires from the connector and check for bad solder connection and/or broken wire. Use your multimeter to prove continuity.

Chosen Solution Half of the screen is blacked out vertically. Could this be a logic board issue? It could be a screen issue (backlight) or a backlight driver (logic board) issue. Did this happen out of the blue or was it following a repair? Board issues can occur when a screen is disconnected (or re-connected) while the battery is still plugged in. The way the backlight driver works is there are two return paths, one for the left side and one for the right side....

Chosen Solution I have an iPhone 6 i had a screen replacement done about two weeks ago because my screen was cracked and it had colored vertical lines on the side and black dots. After the screen replacement my screen is black i tried holding down the sleep/wake button and the home button but nothing work. i opened the phone to make sure the cables wasn’t loose. I was thinking that it was the screen so i had someone look at it and it wasn’t that he tried a new battery and that didn’t work....

Chosen Solution I’m using a Windows laptop, (Windows 7). Had it for a couple years, runs fine. Internet speed is normal, but im trying to restore various iPhones but the software for the updates and iTunes its self won’t download. It says around 120 hours remaining and then errors out. Help? Take a look at your systems resources. Do you have at least 1/3 of the HD free? Have you tried defragmenting your HD?...

Chosen Solution Even when machine is off, the hot water continuously flows. Joni, here is my answer to a very similar question “Since it only happens with your hot water, my money is on a bad hot water solenoid. It apparently does not switch off. You washer should have a water level sensor that sends a signal to close the solenoid. It would do the same to the cold water. You also want to make sure that the pressure hose is not crimped in the cabinet....

Chosen Solution screen rotates into phone screen Hi! To prevent your tablet from rotating its screen to portrait mode, go to Settings, under Display look for an option called “Screen rotation” and set it to disable. Alternatively slide the drop menu down (the one that you would slide down to view notifications) and look for a screen rotation or rotation lock button. Toggle it and you should be good to go....

Chosen Solution My iphone 6 with ios 10.3.1 is stuck in recovery mode, we have tried to fix ios but it fails with error 14, we have tried many pcs and many cables and it seems a problem more than a cable or unupdated itunes. I have no backup and I need my photos and a restore to factory settings is a big loss to me. Is there a way to recover its data ?...

Chosen Solution My power button is stuck and cannot be pressed down to start the laptop. I think its just a purely mechanical problem. But to check that I have to get the cover off. How do I do that ? Follow this guide through step 32: iBook G3 12" Top Shield Replacement You will now have access to the switch. The switch comes with the top case. Here is a list of the available top cases: http://www....

Chosen Solution My disc got stuck in side and it does not read when you plug it in to a computer neither does it give me the option to eject the disc. Does any one have ideas on how to get it to Eject or am i going to have to take it apart . I appreciate the help. Reboot your Mac holding down the eject key on your keyboard. It’s usually the very top right key on the keyboard....

Chosen Solution welli have a Ps2 slim and its reading some discs but some not what to do??? Try cleaning your laser and also check the laser cable - it may be worn/damaged - check out THIS GUIDE THIS is the cable Also have read of THIS ARTICLE there is a white cable near the washer which can be poped up.clean your laser and lens with flash cleaner and with some buds replace your lens....

Chosen Solution Hi guys, I’m wondering if anybody has advice, I was unplugging my hdmi cable and my Xbox feel of table and landed on floor. The unit has no damage, my Xbox powers on ok but doesn’t show anything on the tv and controllers won’t sync with Xbox anymore, also like a ticking sound coming from it when power is on, any help would be appreciated guys as I really do t want to send to Xbox and wait ages for it to be return....

Chosen Solution Firstly, I know very little about electronics. Second, this is automotive related. My question… If an EPROM is damaged (no longer functioning) how do it get damaged? Shorted, Voltage spike, if it’s not physically damaged. Can the programing still be read and copied (to a desktop) correctly? In other words the EPROM being shorted doesn’t affect the ability to correctly read the program correct? Thanx, I know this has nothing to do with cell phones or laptops but hoping someone would know....

Chosen Solution when camera turned on, a message: err keeps flashing and nothing works. manual says press shutter - no change. battery is charged and card is in place. Solution 1. Take the lens off and try to power it on also, Take the battery out and hold the power button and shutter for 20 seconds then proceed to insert the battery again. Does it work? Solution 2. take out the battery and if you can power on the camera without a battery do so, it may force the camera to make a change in its memory and may show a different error msg....

Chosen Solution My DSi turns on gives me the menu but will not let me play any og my games. Just keeps coming up with Error has occurred press button to turn the system off. If your DSi is under warranty you need to contact Nintendo about repairing it. If it is not under warranty you need to replace the logic board/motherboard. Click here and chose the “motherboard” guide for instructions on how to do that....

Chosen Solution Gang, I figure why not DIY my new mini so I got 8G of memory and a OCZ Agility 200G SSD drive. I have put these in several older mini’s. Ok So I replaced the drive and did all the stuff put the DVD install disk in and formated, partitioned and transfered the OS. The problem is the FAN is running full speed. I tried the SMC reset by removing the power cord and pressing the on button for 5 seconds....

Chosen Solution No idea if anyone will have any idea here with MacBook board level repairs. I have a 830-00165 Board that was liquid damaged. I was able to find a short under the CPU last week and got it working. Then it stopped working again after I assembled it. I got to the point where I have replaced the resistor on PPBUS_G3H_R which is R7006. I’m still not getting any image on the screen....

Chosen Solution Hi everyone, I have upgraded my iMac (iMac Intel 27" EMC 2546) with an SSD and unlike most people my fan is actually stuck at idle, no matter the work load. Thus it’s overheating. I can watch the temperature rise on the cpu and yet the fan stays at 1200 RPM. Initially I thought it might be because I had not installed the optional HD temp sensor, so I bought and installed one....

Chosen Solution Hey! I bought a partially broken Macbook Pro Early ‘11 yesterday to repair. The only broken thing about it is this one key that the previous owner must have tried to fix, but failed. See pictures. When i touch the bottom of the key, nothing happens, should it work when pressing the finger, even without the nibble? If so, is a keyboard or upper case replacement the only way to get this fixed?...