Chosen Solution How do I remove my HDD to install a SDD? And what measurements does it have to be? 2.5? Yes, here is the service manual. http://topics-cdn.dell.com/pdf/inspiron-… It appears to be a standard 2.5" laptop hard drive, see page 37.
Chosen Solution Hello everyone. I appreciate when you spend time in my topic and help me solve this problem!. My MBP could not boot anything ( Internet recovery, CMD R, CMD V, shift…) I tried install fresh copy of high sierra but just grey screen with nothing on it? I did try single mode user then I got the screen like this Can you help me with this problem. This most likely happened when you upgraded to High Sierra....
Chosen Solution I am trying to remove the battery from my iPhone 4s and am having a difficult time prying it from the case. I have the plastic tool recommended, but it is starting to weaken and I am afraid to pry to hard in case I damage the battery or the plastic tool. Any suggesstions? Don’t pry the battery, period. I’ve seen countless logic boards damaged due to careless prying....
Chosen Solution Recently I plug my USB cable into my computer and now I cannot get USB mass storage mode off my garmin nuvi 200w The information provided is from here and explains why it does that. “Garmin Mass Storage Mode devices no longer communicate with a computer with the Garmin Protocol but instead present themselves as a USB mass storage device. When a USB cable is connected between a Garmin Mass Storage Mode GPS device and a computer, the GPS device enters mass storage mode....
Chosen Solution So i dropped my phone a few weeks ago and it cracked and the top of the screen became slightly unresponsive. As of today none of the screen is responsive but the image is prefectly ok. Do i need to replace the whole lcd, digitizer and screen combo or just the screen? You would need very specialized equipment to just change the glass itself. You need to change the whole assembly....
Chosen Solution Do you sell iPhone 6 rear mic? Making a recording with rear camera, I get hiss and no sound. It’s built in with the power button and flashlight. iPhone 6 Power Button Cable Hi Daniel, I’m no iPhone expert(quite the opposite, actually), but it appears the iPhone’s mics are built into the frontfacing camera and headphone/charging board. iFixit sells both of these. iPhone 6 Front Camera and Sensor Cable iPhone 6 Lightning Connector and Headphone Jack Hope this helps!...
Chosen Solution About 2-3 months ago, I started getting notifications that my battery needed to be replaced. I never bothered to replace it because I’d rather not waste more money on it. At some point, it wouldn’t last more than 10 minutes unplugged even though it was fully charged. A few weeks ago, I had to perform a custom installation because I got locked out and wanted to save the files (so now they’re all located in Windows....
Chosen Solution Hey, Recently my galaxy s6 fell out of my pocket into a puddle. Everything seems to work okay, but I found that the battery is emitting an excessive amount of heat and I’ve experienced quite a dramatic drop in performance. Sometimes I’ll press the power button and it will take 20 seconds for it to work. I kept the phone on a towel after it got wet for 72hrs and everything seemed to work find for about a day....
Chosen Solution I am a New Tech Repairing Phones. Any other Techs finding extra Screws flouting around in the newer Gen apple phone? I have all screws accounted for but this the 5th phone. I have had extra Screws in it upon opening it. Are you saying that you open up a phone for the first time and already there is an extra screw floating around? If not, how do you keep track of the screws you remove?...
Chosen Solution Hi Could someone help with identifying the fan screws as all three screws is different? I would appreciate it if you could align the colours with the screws?. Regards Paul If you review the guide MacBook Air 13" Early 2014 Fan Replacement Step 9 you’ll see this image which ID’s by color which screw goes were Red in the top right, counter-clockwise Orange and Yellow at the bottom.
Chosen Solution My refrigerator freezer is not freezing i replaced parts for thermostat .thermistor control board. and start relay ,and capacitor all fans are running what else could it be and some frost on one botton coil Hi, Have you checked that the condenser coils are clean and free of dust? What is the temperature in the freezer and refrigerator compartments? You said that there is frost on one bottom coil, do you mean the evaporator unit inside the freezer compartment?...
Chosen Solution I am replacing a shattered back glass on my s7. I have the old glass and all of the adhesive off, but i found a gold mesh looking stuff around my camera that has torn. part of it stayed on the phone and part of it is still on the back glass. does anyone know what it is? I’m not sure what it is but I never put it back because it really has no effect on anything....
Chosen Solution It sucks gas I know it’s a 350 with full time four wheel drive but I should be getting more than 4 mpg I’d take it in to an AutoZone and get a free computer readout to try to see what’s wrong. Also see if the the four wheel is engaged all the time. Hi, Maybe you should consider a tune up for your vehicle. Google how to tune my chev pickup....
Chosen Solution My gear 2 had damaged terminals ( charging pins located in gear s2 back .) So I can not charge it. Please is that terminals is replaceable. And where I can fix it. Same thing happened to me. It’s clearly a defect in manufacturing as I did not abuse the watch at all and the pins are only ever touching your wrist or the charger. The Samsung repair centre said it was physical damage and not covered under warranty....
Chosen Solution This is my second phone with the same problem. I have had a iPhone XR which had ghost touch. I changed to a 7 plus and after using it for awhile. Could someone let me know the cause of this or how to stop it ( yes all updates are updated ). Thanks! Most times ghost touching on an iPhone 7 comes from a screen replacement, after the housing frame has been bumped and the screen doesn’t sit flush....
Chosen Solution Hi OMG same EXACT problem here did you fix it? Please let me know what the problem was thanks. UN55H6350AFXZA I don’t have test light to check voltage. Nothing tried yet HOT CAKES start by disconnecting the cable between the main and power board, if the backlight comes on then you know that it is good. Next measure connector CNM803 (should get ~13V) Next check connector CNL802 (0,0,334v,0,223v,0,223v,0). If your power supply has the right voltages for your backlight and obviously the backlight works if it comes on when you disconnect the main board from the PSU, that would leave the main board as the culprit since it provides the signal for the backlight enable....
Chosen Solution okay so I dropped my when I was at school and when I got home and went to charge it wouldn’t unless I put it some way so I put it on charge went down the steps and when I came back up it wasn’t charging and now my screen wont come on so what I want to know is what’s wrong with it and if its the charger port can it be fixed...
Chosen Solution I have a late 2008 MacBook Pro 15" that needs repair. Someone was too aggressive when installing the Bluetooth/wifi/isight cable and their screwdriver or similar tool slipped TWICE (or more) and they popped two SMD components off the board. I think I have identified them as a 0.1uF ceramic capacitor and a 90ohm choke coil. If someone could verify and identify the exact models I should use to repair that would be great....
Chosen Solution i replaced the battery and the head set and the hold switch with your help . Now i still have no sound out to head set . still dont know if i have sound out of the usb port to a ipod home set . Recheck the headphone jack connector into the logic board. If that doesn’t fix it then your logic board is probably messed up, which means you will have to replace it: iPod Video (30 GB) Logic Board
Chosen Solution Hi, I am attempting an iPhone 6 front panel replacement, but cannot get the last cable connector to fit into the logic board. I am sure I have the cables in the right order. How can I get them connected? Thanks, Ralph. Patience and recheck that the you are following the guide and putting the correct connectors in the correct connections.
