Chosen Solution forgot password at boot up and cant get into windows was woundering how to fix this I assume your running Windows XP. If you have an Administrator account, it doesn’t have a password by default. If you can log in as that, you can change your other user’s password going to Control Panel/User. Select the account and select change password. If you don’t have an admin account, shut down and restart....
Chosen Solution I forgot my password to open my phone! Help! murfo, not much you can do other than trying a hard reset. Follow the instructions on here. This will erase all of your data.
Chosen Solution I installed a new keyboard in the 12 inch ibook, now when it is powered up the screen freezes. I took it apart to check and all steps followed found everything as ifixit showed. Could it be the keyboard or something I might have done? Cindi Hi! Do you have an Airport installed in this machine? The reason I’m asking is that I’ve often found that if the metal Airport antenna plug is left loose and dangling, and the memory shield is not installed, it can short out the computer by touching the memory or other components on the logic board....
Chosen Solution I recently replaced the battery on an iPhone 6s Plus and after the repair the front-facing camera and microphone are no longer working. The only way to make calls is to use a headset. I’ve taken the phone apart again and re-seated all of the connectors that had been removed, yet the problem persists. I’m thinking it could be a logic board problem, but perhaps its the flex cable for the camera?...
Chosen Solution After screen and battery replacement on iPhone SE 1723, all the navigation software started failing to define my position and speed. Eventually, it stopped doing that at all while the compass was working good. My position now is defined approximately only by cellular towers and wifi spots. What can be the cause here? Bad GPS antenna connection? GPS chip needs replacement? Anything else? At the time, the GPS Diagnostic shows “No satellite signal"....
Chosen Solution Hi Can please assis I bought and mac book air use. This is the message the seller send. What.can I do screen shows and question mark This is a used working item in good cosmetic condition that was pulled from a working environment and is guaranteed working as described. Unit powers on and posts to bios. Please note no storage or charger included. Unit failed to detect hard drive installed....
Chosen Solution I was fortunate enough to have the motherboard on my MacBook Pro Early 2011 replaced by Apple at no charge. But after a week, I noticed a horizontal bar appears across the screen upon booting up. It only last for a few moments and doesn’t appear again while I’m using the MacBook Pro. I think there’s a firmware upgrade I can do for the video card. I found a file on the Apple support page that would do just that....
Chosen Solution I would always unplug my PS3 40gb and take to my friend’s house. But recently the picture will only stay on the television if the cable for the AV multi slot is in a certain position. If i remove it from that position it takes about 20min to find the “sweet spot”. Now my PS3 is stuck in a uncomfortable position in my home and if I move I’m worried that I will forever lose the signal....
Chosen Solution apparently, there is a bad connection. The power button does not work properly. depending on how you hold the earbuds, the button powers on/off by itself. the volume buttons are not working at all. Hey, I had similar issue with my bluebud X Volume button work perfeclty, but power button work half the time, and stick when working (button stay down witch result in power off after 2 sec) Source of problem: After dissasembly, i realise the metal cup making contact for the power button had moved Short answer: replaced the metal cup to it’s original place Long answer: remove the back cover of the button-mic assembly (8 small clib, 4 per side) remove the red holder (6 clip, 4 per side) be extra carfull with the small wire ( i recomande taping the earphone on a table will working to eleminate any strain on those wire) remove the board (mine was slightly glued in place) remove the tape holding the metal cup place new tape on metal cup Place tape + metal cup dead center on the + sign on the board (do not block the mic hole) power on earphone to test reassemble carefully (don’t pinch small wire) Picture while disasembled: https://s13....
Chosen Solution Hi, I spilled something over my keyboard and some keys just keep messing with my macbook. I do have a external keyboard that works fine. I tried to disconnect via the terminal way but its not really practical. I like to just disconnect my keyboard. So i just need to know wich cable to pull from my logic board. Thanks! Not an option here. You need the keyboard connected as the power switch is part of it....
Chosen Solution Hey, I needed to replace the display of an S8 Plus. Unfortunately it doesn’t charge after the replacement. The temperature is too low. I tried a new battery and the phone starts but still it won’t charge and I get the same error that device temperature is too low. Any ideas? Hi. I had the same problem for 2 s8 and s8+. Try to assemble the whole phones, including screws, without back cover and put it in charge....
Chosen Solution My wireless card is enabled but I do not see any wireless signals. I tried connecting through a USB ethernet adaptor and the internet works fine. Why is my internet not working? The wireless issues could be caused by various issues. The Wi-Fi card may not be seated in the miniPCI Slot. You may have to download the driver for your Wi-Fi card. You may have to enter a password to access the wireless network....
Chosen Solution Hello, i know that hard oled and soft oled can restore true tone, but can you restore true tone on cheap lcd display? Or only specific displays are able to restore it? Cause I have one lcd no matte how much I rewrite the data it won’t restore, on a soft oled it worked successfully some lcds do not support true tone, so it doesnt matter if its hard or soft
Chosen Solution Our label maker is stuck on text setting with two lines. How do we reset it? Have read the instructions where it isn´t told and tried “everything”. Hi @ullis , By " tried everything" does that include a power refresh? If not try the following: Remove the batteries from the device. Press and hold the power button on the label maker for about 10 seconds to remove any residual power left in the device....
Chosen Solution I have very little IT knowledge so am probably asking a stupid question! Basically I’m a school teacher and a student accidentally broke the plastic face plate off of my DVD drive. I now can’t find the original bit of plastic anywhere so would like to source a plastic face plate for the DVD drive am hoping it’ll slot back on as everything else is working fine. However when I’ve googled I can only find entire new optical drives for this model of laptop....
Chosen Solution Yesterday i repair my MBP ( Nvidia Graphic Chip ). Now he is running but the fans turns constantly 6000 rpm. it may be that I forgot to connect a cable? The temp sensors work correctly according to istate pro. Please help me ps. sorry for my bad english :) You haven’t given much information to go by, including the readings from iStat. You may have a process such as a stuck print job causing your processor to run in excess....
Chosen Solution Cadillac ‘96 2dr LTD My fuel door and trunk lid are requiring about 20 attempts to open with both the remote and interior buttons. This began all of a sudden. Anybody know a fix? My thoughts on this: 1st: how long has it been since you changed your battery in your remote? I find that mine last about a year to two years before having to replace. 2nd: if you do not drive the car much you may have got the lube on the actuators hardened from lack of movement....
Chosen Solution When bike is running fuel flows out of a black rubber hose cut on an angle.bike runs great.hose goes to right side of carburetor. Sounds like a leaking fuel hose, I would replace it. Does it have clamps there it attaches to the carb and fuel tank? Hoses tent to break due to vibration and ageing, if you can see it, it would be easy to replace, you don’t specify exact model, but Yamaha usually has special hoses you have to replace with (90 degree, or specific distances), buying an exact replacement is the easiest way of replacing, but a normal hose cut to the distance could be used too if it is not so bent that blocks the fuel flow… Up to you to decide, they used to be cheap at Yamaha… Also hoses tent to have pressure clips on each side, please confirm the fuel comes from a broken hose, and not from a missing clip on one of the sides....
Chosen Solution Hi techs One of my costumers brought this iMac for repair, it was working fine while watching NetFlix and then, the screen went dark but voice still working. I put the light on the LCD and I was able to see the apps, I plugged it to TV screen and it works just fine. Any help with that please? Is there any fuse or a component for the backlight I need to check ( similar to the filter of iPad mayber ) ?...
Chosen Solution My Roku screaming stick works fine on my other Phillips brand TV no problem , but the TV in question blinks continuously while screaming with the very same Roku screaming stick . On the TV in question there’s 3 HDMI ports , and they all yield the same problem . The TV’S are both 2012 models . My internet connections are all secure , running at 60-71mbps . My other television performs masterfully , using the exact same screaming stick , the very same one ( not just meaning the brand ) ....
