Posts

Chosen Solution What’s wrong and how do I fix it? mkoch, If it is new, did you remove the tape, from the lower base body split section, if not remove before turning on any more or damage to internal gear could occur. Recheck that the fan is still assembled correctly and locked in correct position. Install new batteries in remote and try. If all looks good and still under warranty return for repair/replacement/refund as there may internal damage to oscillating gear....

Chosen Solution I’m having the same problem with my LG fridge I pulled connector off PCB board tested first prong and last prong mine jumped around a bit but never seen 200Vac .So what does this mean the problem could be? @b o Smith if you disconnect CON201 and after plugging in the refer , within 30 seconds of pushing the test button you should have at least 200v. If you don’t, then you have a bad control board....

Chosen Solution Okay so I have been looking literally everywhere possible to try and find a reprogrammer for iPad so that I can get the True Tone functionality back once I replace the screen. Is there a reprogrammer for iPad screens out there somewhere and I just missed it or am I just going to have to go through Apple to get True Tone on my iPad like I had before the screen was destroyed?...

Chosen Solution How do you do a hard reset on a iPhone 3G 16mb. simply press the home and the sleep button at the same time until the phone restarts - this should take around 10 seconds You should hold down the home screen button and the top lock button together , KEEP HOLDING EVEN WHEN IT SAYS TURN OFF, KEEP HOLDING UNTIL THE APPLE APPEARS ,then release both buttons and wait for the phone to reboot....

Chosen Solution Why is my microphone picking up static noise? I tried unplugging it and it is still picking up static This could be one of many issues. First, it could just be a broken microphone, you can easily purchase a new one and simply replace the part. Other than that, it could also be a broken headphone jack. Before assuming it is broken, use a flashlight and make sure the port is clean because any debris can cause static, or failure of the component....

Chosen Solution I have lg 42lk550 hit power button no picture or sound Jeff Hafely start off by checking for power to your TV. Check the outlet and the cable. After that remove the back of your set and check the power going to the power supply, then the fuses on the power board. Check those for power as well as continuity. You will need a multimeter for further testing.Post some images of all of your boards with your question so that we can see what you see and guide you through some more tests....

Chosen Solution (The lid itself doesn’t seem damaged) This happened on back-right side of my laptop. 2 years ago I accidently banged it against a wall. It wasn’t that bad (these images are from 2 days ago), so I left it, because the parts would shift back when I pushed the panel back in (it wasn’t as bad as in these pictures).But just a few days ago, I tried to close my laptop only to notice that the damage has greatly increased, and that the panel on this corner is coming off (the rest of the laptop is completely fine)....

Chosen Solution Is there an adapter I can use to be able to connect wired headphones (stereo jack rs232)? This unit only has optical output jack. If it has an optical out, you can use this to convert it to a headphone output: https://www.amazon.com/gp/aw/d/B01N2Z21I… Hope this helps!

Chosen Solution I’ve owned this Logitech Lapdesk for several months and basically it is a good thing. The design is great, it looks good ,it is comfortable and small and compact. It does everything I want except hold my MacBook! The computer is constantly sliding down the smooth incline surface. What were those engineers thinking? I am a cabinetmaker and would like to veneer the desk surface but I can not find the key for pulling the thing apart....

Chosen Solution how do i get my messages to stop talking my letters outloud It’s possible that it is on hands free mode that will be in your settings .most likely to be under device section. Scroll down it should there. And if you have it on then you can turn it off or if you have it on then do this .Hold the volume button on the phone the slider bar will pop up on screen keep holding look there you will see a icon like gear let go volume push the icon you can operate all sounds of the phone media, notification s, ringtone,,phone hope this helps....

Chosen Solution how to adjust screen brightness Hi, Here are the instructions on how to adjust the brightness of the display. Here is a link to the User manual for your laptop. http://h20566.www2.hp.com/hpsc/doc/publi…

Chosen Solution I checked out the test sheet for this device, and it refers to a service diagnostic test mode. Unfortunately, the given instructions (press any button in a 2-second-on, 2-second-off repeating pattern) don’t work for my dryer. How do I enter service diagnostic test mode on my dryer? On my dryer, Model 110.94832201, the method for entering service diagnostic test mode is different: press the “more time” and “less time” buttons in an alternating sequence, completing four presses (2 of each) within 5 seconds....

Chosen Solution How do i replace the full housing with all side flaps and chassis while keeping it waterproof First, buy the original full housing replacement with adhesive sticker. Then, prepare the back cover adhesive sticker you need, must be original and waterproof. Next, remove and install the small parts inside carefully and correctly especially pay attention to the headphone jack. If you remove it and you’d better use the glue to fix it when put it back....

Chosen Solution Hi, I’m searching for options to connect an external monitor (min resolution 1920x1080, fast refresh not needed) to my MacBook Pro 15” 8,2 Late 2011. I disabled dedicated GPU via hardware fix, so any Thunderbolt to video adapter doesn’t work. I checked USB Displaylink adapters, but I’d like to know other viable options before buying. Any hint will be really appreciated, thanks! G. No hints, external monitor is controlled by the dedicated GPU, if that’s disabled say goodbye to the chance to drive the image outside of your Mac....

Chosen Solution I accidentally broke one of the bronze-teeth like, the ones underneath the charging port connector. The power of my phone seems to go down fast. Do i need to replace the logic board or i is there any way to replace just the socket. You can replace the socket, but it needs to be microsoldered back on. It is probably better to have it fixed than replaced, so take it to a near-by microsoldering tech and see if they can solder a new one on

Chosen Solution My wife dropped her iphone and the following happened: Black screen followed by a blue screen then black again.Phone was responsive, can fill vibrate etc.I powered it off hoping to restart it and I couldn’t determine it if came back on (itunes didn’t recognize)Bought icloud locked phone off ebay that appeared to be good and workingReplaced battery and lcd using the icloud locked phone and now I can access my phoneThe following doesn’t work: headphones, mic, charging, connection to itunes, front camera, ear piece....

Chosen Solution Good afternoon, An acquaintance dropped her phone, after which half of the screen worked for an instant, but then went dead. She would like to have the photos restored that were on the phone (internal memory!), but I think it would be a fun challenge to see if the phone can be repaired After connecting to the charging port, the charging light flashes. Shining a flashlight on the screen doesn’t show anything, the screen really seems completely dead....

Chosen Solution Dryer doesn’t get hot! Cause 1 Thermal Fuse The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good....

Chosen Solution I bought a brand new DVD to play in my old DVD player it started Make a lot of noises n started to skip scenes n freeze, i cleaned the laser and put the the DVD back in player stilk the same result play good all the way to the end of movie n then started skipping n freezing so threw the old player away. Bought a new DVD player n now put the same DVD disc on and starts off with the opening scripts then goes directly to halfway to the movie then goes to 1/4 way to the end then goes to the begining n then back to the end then halfway then goes to end credits it’s like all the scenes are jumbled up now I’ve tried other discs that I played in my old DVD player and those discs play just fine confused why this only DVD does that...

Chosen Solution I already did the sync and eject menu to factory reset my Xbox. It registered the reset request but now Everytime it tries to carry out the reset it says error e106 and I’m stuck in an endless loop where my Xbox won’t reset itself please help. Any answers are appreciated Solution 1. Clear the cache Xbox One error code e106 is a system error caused by data cache....