Chosen Solution Today my kenmore h3 washer gave me the code F02. I looked it up and found that it means drain problem. First I checked the drain hose and there was no blockage. Next I checked the pump filter where I found some rocks a wirde red rubber piece and a metal pin that could be part of washer or could be some wierd hair thing for all I know....
Chosen Solution I purchased the rechargable battery upgrade for the Grace Digital Mondo. How do I install it? After you add the extended battery upgrade, you may have problems with power. If this does happen, refer to our troubleshoot to identify any issues your having with your device. Hi, According to this link there are only 3 screws visible from the exterior of the product, and two of them are sunken so as to not be immediately obvious....
Chosen Solution Sorry if ive been asking to many questions. Now I would like to find out how to fix the wire that is disconnected to the power supply board i just discovered. . sorry i dont know the trminology. Wait upon further review of the tv i found this also some kind of whiteweird stuff on the back of this board thanks for your time everyone i do appreciate it...
Chosen Solution Hi, I have an RCA 7 Voyager II tablet (RCT6773W22B), and when I use the stock launcher that came on the tablet (Launcher3), every time I either exit an app or rotate the tablet on the home screen, I get an error message that says: “Unfortunately, Launcher3 has stopped.” I’m using Nova Launcher at the moment but I want to go back to the stock launcher so I can free up some space....
Chosen Solution Hello! In our store I’m win two 2gb modules of DDR3 1333mhz RAM (so-dimm). This memory can work in this mac mini (A1283)? Thanks! Even in the 2010 Model of Mini, the system bus is 1066Mhz, so I believe that you can use this RAM, but your system is only going to recognize 1066mhz, its an EFI limitation on your logicboard itself. On a PC you would be able to fiddle around with the bios and allow the machine to recognize all 1333 MHZ, but the difference wont be noticeable....
Chosen Solution I have a Galaxy Tab 4 8 inch from T-Mobile. It works great but recently I have had trouble with the touch screen. I tried a factory reset and the problem still persisted. The touch screen works for the most part but the top 5% of the screen just doesn’t respond to touch. I installed a touch screen tester where you draw across the screen and it is definitely the top 5% of the screen below the Samsung logo....
Chosen Solution I think my two year old might of hit my tv. It’s this fixable or do I need to replace the tv? Ouch, I’m afraid we have bad news. The LCD is definitely broken and they’re not repairable. You don’t mention what size your TV is, but on most modern large screen televisions the cost of replacing the LCD will usually exceed the price of just buying a whole new one....
Chosen Solution Just wondering if the 2012 hard drive cables work fine in 2009/2010 Macbook Pro 13" models? 2009/2010 cables seem like they are more likely to fail than the newer cables, so I would prefer to fit these rather than the older cables. Thanks :) The cable will work fine. Issues you may have are you may only be able to secure the cable with one screw. MacBook Pro 13" Unibody Mid 2010 Hard Drive Cable Replacement If the bracket that holds the hard drive in place hits the new cable, I break it and use just one end....
Chosen Solution Why won’t my drone fly forward when I push the lever on the remote? Hi, I am interested in getting drones to work. I have 19, most are second hand. 14 are now going, with 5 on the working on them stage. One of the most important things I have found is to do your compass calibrations .
Chosen Solution emachine beep when start up blank screen The emachine beep codes depends on the type and version of BIOS and motherboard, and the easiest way is to contact emachines support. Some motherboards may have special beeps. http://www.emachines.com/support/tech_su… Here is a general listing of the beep codes depending on the BIOS http://www.pchell.com/hardware/beepcodes… You could try to pull all your memory sticks and reseat only one of them. If you continue to get the same error, change it for a different memory module Good Luck
Chosen Solution pls my Honda Accord 2000 salon jerks and exhibits rough idling, i have changed the plugs, and even the fuel pump but its still the same Take it to an Auto Zone and get a free computer read out to know how to proceed and where the problem is. They will be happy to even sell you the parts you need.
Chosen Solution Hi every one! I erased both partitions on my drive using disc utilities by mistake. I guess I erased the hidden recovery one also so now can do anything and have no OS that came with it. What should i do? There are a few ways you can still recover things here. First, Do you have something on the drive which you need to recover? If you do, you’ll need to find a friend with a Mac that you can connect your Mac to using Target Mode (see below on how), then using a file recovery program try to recover your files....
Chosen Solution I replaced my Apple Watch series 5 44mm lte force touch gasket as mine was damaged when I was replacing the screen (I need to reset it using the force touch as it is password locked) and when I replaced it and tried to do it, it still did the same thing. Any ideas on what might be wrong?? So it turns out i needed too hold the power button (with it charging) then hold the crown....
Chosen Solution I had the same model and same issue. I disassembled the pump / motor assembly and found the motor to be broken, so I ordered a replacement motor and tested it OK before putting it on. The problem persisted with the replacement. I entered Drain model (the display showed DRAIN 001, 002, 003 ‘minutes’) but found no power to the motor at all. Tried reset by pressing three buttons next to START button and received error codes....
Chosen Solution The led charging status light is always on. The battery won’t charge through the macro USB port and when I plug the calculator into my computer it isn’t recognized. The easiest possible fix is to try and push the cable into the calculator’s port harder. You’ll have to plug it in harder than you’d expect, you’ll feel a click when it’s properly connected. If that doesn’t work, this could be the result of a faulty cable....
Chosen Solution Hello, unfortunately the Heat-Sink-Sticker (see picture) was damaged (destroyed) while cleaning my iPhone camera. Can someone tell me how to replace it and especially where I can get a replacement? Thank you! These are not easy to find but I did find a listing here. I don’t think it will have any impact if you don’t replace it though.
Chosen Solution I can’t use the mouse or keyboard. It won’t allow me to turn it off. Hi, You can ‘force stop’ your PC by pressing the power button until it shuts down. When you start it again you will get a message that Windows did not shutdown properly and a screen will give you options on how you want it to start. You can select’safe mode’, let it boot all the way to the desktop (it will have safe mode written in the 4 corners of the screen....
Chosen Solution So i bought this thinking i could fix one of my other ones, Anyway when it arrived, i plugged it in and nothing, I thought something was unplugged inside, so I took it Apart nothing was unplugged, So i tried the keyboard on one of my other laptops, still nothing Nothing What the heck is going on?@danj There is a onboard battery checker within the battery. locate the LED’s and the small button on the battery....
Chosen Solution Hi i recently replaced the lcd on my iphone 5s and everything worked fine and after one week home button stop working.I restarted my phone and it says : Unable to Activate Touch Id on this iphone So idk if it is because of replace of lcd ( flex cable broken?) but it worked after the replace and my phone didnt fell or something . It is possible to be software error with ios 11 update ( My battery started to drain after update extremly too)....
Chosen Solution Glove box handle broke and I fixed it but have no idea how it mounts. Is there an illustration somewhere that shows how it mounts? here (click) is a link to mini2.com. there is a pdf and some instructions good luck I recently replaced mine. Couple of screws across the top, two on either side, and one torx in the back. There’s a vent tube that you place in after the replacement, and the valve connection for this you have to transfer from the old box (this was a very tight for both the old and new box so be careful, it’s twist-lock, a lot of wiggling and cursing)....
